There is no point in proceding until the media share appears in the output. IPC$ IPC IPC Service (FreeNAS 11 Server ) TheĬonfirm that the media is available over SMB by: $ smbclient -L //192.168.88.22ĭomain = OS = Server = I have a FreeNAS 11 server configured to provide media shares over SMB. Since this is primarily being done to get a Plex Media Server up and running,Īccess to media is, of course, a key part of the system. Freenas update plex media server install#I also installed a few essential tools: $ sudo apt-get install emacs-nox Starting/stopping interfaces and suggested reboot. Research said that there could be problems with Once this change is made, the following should make it take effect: $ sudo ifdown ens18 & sudo ifup ens18Īfter the up/down i had intermittent problems with the IP disappearing andĬhanging back to DHCP. Replaced it with the following (in /etc/network/interfaces): auto ens18 I removed the ens18 configuration that was created during the install and The network device that PVE provides to the Ubuntu VM is named ens18. Storage->Volumes->ViewVolumes confirm that the volume exists. Storage->Volumes->ViewDisks and confirm the two 8TB drives are there.Īdd mirrored volume consisting of both disks named 'vol1' When it reboots, use PVM to access the console.Ĭhoose 1) to configure the network interface.Īccess the system now via for the remainder of the Qm set 100 -virtio3 /dev/disk/by-id/ata-WDC_WD80EFAX-68LHPN0_7SGK1PGCĬonfirm via 'cat /etc/pve/qemu-server/100.conf' After install, shutdown VM.Īdd the two devices to the VM as passthrough. Note that 'ls /dev/disk/by-id' will show each disk ID and a link to the /dev/sd?Ĭreate FreeNAS VM on PVE. Tell PVE to use tank/vmdata for VM and Container storage. Zfs set compression=on tank Tell PVE to pickup the storage Freenas update plex media server plus#Shows all zfs filesystems -> the single pool 'rpool' plus the other zfsįilesystems that PVE created for its use.Īta-WDC_WD80EFAX-68LHPN0_7SGJ4H6C /dev/sddĪta-WDC_WD80EFAX-68LHPN0_7SGK1PGC /dev/sde Therefore, it's important not to change device locations. Theseĭevices are assigned based on when and where drives are inserted/removed. Note that this creates the pool 'rpool' with /dev/sda and /dev/sdb. Router, configured as bridge w/ static IP: 192.168.88.9 IĬonfigured the DRAC to have an IP address of 192.168.88.30. The DRAC provides a means for out-of-band management of the R610. I'm using a Dell R610 server with 64MB of memory. It is very easy to setup using the plugin/jails system.Possible duplicate content with plex-ubuntu-proxmox Server Hardware Why don't you just run Plex on FreeNAS? That seems like the simpelest solution. Freenas update plex media server windows#iSCSI the pool to Win2k16 and create and share the shares using Windows (Seems a bit roundabout to me) Continue as is - FreeNAS shares the folders, Win2k16 Plex maps them like any other computerĢ. I've also created a second VM for Win2k16 running Plex.Ĭurrently I'm using FreeNAS to share the RAIDZ1 pool to various shares, and on the Win2k16 server, I've mapped the shares to drive letters and I'm using them for Plex.Ĭan I (And if yes, should I) use iSCSI on the RAIDZ1 pool to give the Win2k16 server "direct attach" access to the pool for purposes of streamlining Plex? I would prefer FreeNAS to still handle the Shares, but for the Win2k16 server to also get iSCSI access to the same folders. My HBA is using PCI Passthrough to a FreeNAS 9.10.2 VM. I finally got some progress done on my server Reno and I've made a lot of progress.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |